ImageGreetings! Welcome to Tezzaworld website, unfortunately you are a few years late to the show as nearly everyone has been and gone, there is still lots of useful archived material to read through, not many active users unfortunately, but that’s the way it goes, hopefully you are not too disappointed...

Search found 31 matches

Go to advanced search

by stabby
Thu May 18, 2017 6:22 am
Forum: Engine & Transmission section
Topic: IS300 Clutch Master Cylinder
Replies: 1
Views: 698

IS300 Clutch Master Cylinder

Would anyone know if the is300 clutch master would fit in place of an altezza clutch master cylinder? Mine is leaking and thought it would be better to just replace it with the is300 version since that is more readily available than the altezza version. From the looks of it it would fit where the tw...
by stabby
Sun Mar 20, 2016 4:43 pm
Forum: Problems with your Altezza
Topic: Altezza EFI relay buzzing noise
Replies: 1
Views: 965

Re: Altezza EFI relay buzzing noise

Don'y know if you managed to solve this buti had the same issues..swapped out the motor plugged everything back up and worked fine for a week.. after a week started to receive on/off check engine lights at various intervals..did a scan on the engine and it gave me a code P1656 which is for the OCV C...
by stabby
Fri Dec 18, 2015 3:24 am
Forum: Brakes and Suspension
Topic: Rear Suspension Torque Specs
Replies: 0
Views: 5385

Rear Suspension Torque Specs

I'm trying to find the rear suspension torque specs for the Altezza. So for the rear lower arm, upper arm, toe control and traction rod. What also would be helpful is the torque specs where the differential bolts on to, exhaust etc. Basically everything from the rear :) Just wanting to do the fasten...
by stabby
Sat Jan 17, 2015 5:41 pm
Forum: Brakes and Suspension
Topic: Braided stainless steel brake lines
Replies: 4
Views: 1502

Re: Braided stainless steel brake lines

Package arrived the previous week but managed to install the brake lines this week. Below an image of the package contents. You get the brake lines, screws and washers, instructions and even stickers! :) http://i60.tinypic.com/143q5tw.jpg Now in the instructions is where the secret lies of why this ...
by stabby
Tue Dec 23, 2014 12:49 am
Forum: Brakes and Suspension
Topic: Braided stainless steel brake lines
Replies: 4
Views: 1502

Re: Braided stainless steel brake lines

excuse the delay..but kept searching online for a solution and found one that could work.. apparently the is200 HEL brake lines could fit on our japanese version car. I talked with Ben Viner from HEL automotive and he assured me that it could fit on our cars. So ordered a package and now we wait til...
by stabby
Wed Dec 10, 2014 3:41 pm
Forum: Brakes and Suspension
Topic: Braided stainless steel brake lines
Replies: 4
Views: 1502

Braided stainless steel brake lines

Hello everyone, Wanted to improve the braking on my car a little by upgrading the stock rubber lines for braided stainless steel ones. But what kept me from ordering is knowing that up to an 05/2000 model altezza the flare that connects to the brake lines is of a S-type. 05/2000 and later models hav...
by stabby
Fri Jan 24, 2014 4:02 pm
Forum: Engine & Transmission section
Topic: just installed 4.88 final drive......
Replies: 4
Views: 890

Re: just installed 4.88 final drive......

wow nice to hear this..but where did you get that from?
I know the trd version only goes up to 4.55..what brand is yours?

And was it difficult to install?
by stabby
Sun Jun 23, 2013 1:52 pm
Forum: Engine & Transmission section
Topic: power steering pump replacement
Replies: 9
Views: 2012

Re: power steering pump replacement

Thanks alot peter0991..
by stabby
Thu Jun 20, 2013 5:18 pm
Forum: Engine & Transmission section
Topic: power steering pump replacement
Replies: 9
Views: 2012

Re: power steering pump replacement

hey peter0991,

what size belt did u use to use just the powersteering?
may be interested to do this in the future....
by stabby
Mon Jun 17, 2013 11:36 pm
Forum: Problems with your Altezza
Topic: power steering bleeding
Replies: 13
Views: 2738

Re: power steering bleeding

just wanted to know if you jacked up the car..
i did this last time and when the front wheels were in the air..then turning it left and right..
Try giving it some gas too..

Let us know if this helped..
by stabby
Fri May 31, 2013 2:28 pm
Forum: Engine & Transmission section
Topic: What parts needed to replace clutch?
Replies: 6
Views: 1598

Re: What parts needed to replace clutch?

ok thanks for the info Evelyn.
The part number for this is: 90105-12312.

I think I'll be going with this setup. But not for now. Just wanted to gather some info before making my purchase in about a month or two.

Thanks for all and will keep you posted once I have the items.
by stabby
Mon May 27, 2013 7:40 pm
Forum: Engine & Transmission section
Topic: What parts needed to replace clutch?
Replies: 6
Views: 1598

Re: What parts needed to replace clutch?

Haha..yeah that chirping is really annoying..especially in the morning..
And normally I just go to the site and select my car from the lists that they have (japan, 1999, altezza, sxe10 etc etc)
So the clutch release bearing is: 31230-53010, spigot bearing: ?, rear engine seal oil: 90363-12004?
by stabby
Mon May 27, 2013 6:40 pm
Forum: Engine & Transmission section
Topic: What parts needed to replace clutch?
Replies: 6
Views: 1598

Re: What parts needed to replace clutch?

Hello poTTa, thanks for the information. Some more questions came to mind.. Is the Exedy HD kit somewhat similar to the oem one? does it require more pedal pressure..smooth driving? With all the changed parts do you still hear the squealing and chirping from the transmission? And do you know the par...
by stabby
Mon May 27, 2013 3:35 pm
Forum: Engine & Transmission section
Topic: What parts needed to replace clutch?
Replies: 6
Views: 1598

What parts needed to replace clutch?

Blessed week to you all. I'm planning to change my clutch in about a month or so and wanted to gather some information before making a final order. Ofcourse that parts that would need to be replaced are the clutch, clutch cover and the flywheel? Not too sure about the flywheel, but if needed would i...
by stabby
Mon May 27, 2013 3:05 am
Forum: Newbies - Check-in here!!
Topic: Newbie Curacao
Replies: 14
Views: 767

Re: Newbie Curacao

Welcome to the club and you can always find what you need here. If not you can always ask ;)
And your welcome to join the local altezza crew too..let me know when interested..

Go to advanced search